Excel Scientific

PCR & qPCR Film

4" Soft Rubber Roller

4&quot; Soft Rubber Roller (RL-PLT-01) by MBP is a reusable hand-held sealing tool with a 4-inch (10.16 cm) wide soft rubber surface that applies even, consistent pressure across a full microplate in one pass. Ensures complete adhesion of any MBP plate sealing film — no bubbles or lifted edges. Single unit. Ships ambient.

Application

Material

Manufacturer

<h2 dir="ltr">What are light-sensitive sealing films?</h2>
 Light-sensitive sealing films are light-blocking microplate seals &mdash; typically aluminum foil or opaque pigmented polymer &mdash; used to protect photosensitive contents from light exposure during incubation, detection, and storage. They prevent the photobleaching of fluorophores and the photodegradation of light-labile reagents and drugs, while still stopping evaporation and well-to-well contamination. Foil versions also block gases and tolerate &minus;80 &deg;C storage, and several are pierceable for robotic access. Buy from this category whenever a sample's signal or stability depends on keeping light out of the wells.
&nbsp;
<h2 dir="ltr">What you will find: </h2>
<ul>
<li dir="ltr" aria-level="1">
Black opaque sealing films for full light protection
</li>
<li dir="ltr" aria-level="1">
Semi-opaque light-reducing films for controlled exposure workflows
</li>
<li dir="ltr" aria-level="1">
Standard formats for 96-well microplates (approx. 127 &times; 80 mm)
</li>
<li dir="ltr" aria-level="1">
384-well compatible sealing films for high-throughput assays
</li>
<li dir="ltr" aria-level="1">
Adhesive sealing films for secure microplate closure
</li>
<li dir="ltr" aria-level="1">
Optical-compatible films for fluorescence-based assays
</li>
<li dir="ltr" aria-level="1">
Pierceable and non-pierceable film options for workflow flexibility
</li>
<li dir="ltr" aria-level="1">
High-barrier films for evaporation and contamination control
</li>
</ul>
<h2 dir="ltr"> How to choose light-sensitive films</h2>
&nbsp;
Confirm full light-blocking Choose fully opaque foil or pigmented film, not tinted clear film, when contents are strongly photosensitive; foil blocks light completely, while pigmented polymer films balance light protection with easier handling.
Decide whether you still need optical access Light-sensitive films are not for reading through; if a protocol requires both light protection and optical detection, seal for storage with an opaque film and switch to an optical film at the read step.
Check temperature and storage rating Foil light-blocking films often double as cold storage seals rated to &minus;80 &deg;C, suiting light-sensitive compound libraries; confirm the stated range before archiving frozen samples.
<h2 dir="ltr"> Compare light-sensitive film variants.</h2>
&nbsp;
<ul>
<li data-section-id="17gvbe2" data-start="0" data-end="165">Opaque aluminum foil: Provides maximum light blocking and supports &minus;80 &deg;C storage; compatible with storage and polypropylene plates, as well as robotic probes.</li>
<li data-section-id="1jnkzrj" data-start="167" data-end="335">Pierceable foil: For photosensitive high-throughput screening (HTS) and automated sample access; compatible with polypropylene plates and liquid handling systems.</li>
<li data-section-id="1o0gauf" data-start="337" data-end="479" data-is-last-node="">Black/amber polymer film: For light-sensitive applications requiring easier benchtop handling; compatible with assay and culture plates.</li>
</ul>
<h2 dir="ltr"> Specifications context</h2>
 Light-sensitive films are characterized by opacity, temperature range, and whether they are pierceable. Aluminum foil offers complete light blocking plus a gas and moisture barrier, and often carries a &minus;80 &deg;C to +110 &deg;C rating for combined light protection and freezer storage. Pigmented polymer films are easier to handle for benchtop work. Because a conformable foil presses down into each well, it leaves a defined impression around every well that lets the user confirm a complete seal by eye, and the opaque, intact layer doubles as a tamper-evident and contamination barrier while plates move between the bench, incubator, and freezer. Because these films are not optically clear, they are removed before any fluorescence or absorbance read. As of 2026, they ship in packs of 100 or rolls in a low-to-mid price tier.&nbsp; 
&nbsp;
Instead of struggling with inconsistent results, choose a sealing solution designed specifically for light-sensitive work. <a href="https://mbpinc.net/contact-us">Connect with the MBP team</a> to find the right film format, compatibility, and bulk supply option for your application.

Light Sensitive Film

AbsorbMax™, Fluorescence assays, light sensitive sample protection, -40°C to +80°C, 50 Sealing Films/Pack

AbsorbMax™ (BK-50) by MBP is a black vinyl plate seal for fluorescence assays and light-sensitive sample protection. Opaque black film applicable to either the top or bottom of the plate. Blocks ambient light to protect photosensitive samples and reduce background fluorescence. 50 films/pack, &minus;40&deg;C to +80&deg;C. Ships ambient.

Temperature Range

<h2 dir="ltr">What are cell and tissue culture sealing films?</h2>
 Cell and tissue culture sealing films are breathable, gas-permeable membranes applied to multiwell culture plates to maintain sterility and limit evaporation while letting oxygen and carbon dioxide pass through to the cells. Unlike airtight polyester or foil seals, the porous membrane supports aerobic respiration, so cultures stay viable through multi-day incubations, shaking, and even plate inversion. They use a medical-grade, non-cytotoxic adhesive and suit polystyrene and polypropylene culture plates. Buy from this category for live-cell, tissue, and microbial culture, where gas exchange and sterility matter more than an airtight seal.
&nbsp;
<h2 dir="ltr">What you will find:</h2>
&nbsp;
<ul>
<li dir="ltr" aria-level="1">
Gas-permeable sealing films for optimal cell growth conditions
</li>
<li dir="ltr" aria-level="1">
Adhesive sealing films for microplates and culture plates
</li>
<li dir="ltr" aria-level="1">
Optical clear films for microscopy and imaging applications
</li>
<li dir="ltr" aria-level="1">
Pierceable films for repeated sample access
</li>
<li dir="ltr" aria-level="1">
Sterile sealing films for contamination-sensitive workflows
</li>
<li dir="ltr" aria-level="1">
Heat-resistant films for incubation and thermal applications
</li>
</ul>
<h2 dir="ltr"> How to choose cell and tissue culture films</h2>
&nbsp;
Confirm gas permeability Choose a hydrophobic, gas-permeable membrane with a defined pore size &mdash; commonly around 10&ndash;50 &micro;m &mdash; so O₂ and CO₂ exchange freely while liquid and contaminants stay out.
Verify the adhesive is non-cytotoxic For live cells, select a medical-grade, non-cytotoxic adhesive; the standard pressure-sensitive adhesives used on storage films are not validated for cell contact.
Match the plate and culture format Confirm the film fits 96-, 384-, or deep-well culture plates and supports shaking or inversion if your protocol requires it; deep-well cultures place more demand on the seal.
Decide on sterility and imaging Choose sterile film for cell work; if you image during incubation, select a film with optically clear windows so plates can be read without unsealing.
<h2 dir="ltr">&nbsp;</h2>
<h2 dir="ltr">Specifications context</h2>
 Culture films are defined by gas permeability, pore size, adhesive biocompatibility, and sterility. A porous membrane with 10&ndash;50 &micro;m pores and high moisture-vapor transmission supports aerobic metabolism while limiting evaporation. A medical-grade, non-cytotoxic adhesive keeps cells viable, and sterile packaging prevents contamination of primary cultures. Some plate-reader manufacturers recommend a breathable moisture-barrier seal to prevent moisture release into the instrument. Because the membrane is gas-permeable rather than airtight, a breathable culture film is removed and replaced with an airtight foil or polyester seal before any subsequent freezing or chemical-processing step, where evaporation control and a full barrier &mdash; not gas exchange &mdash; becomes the priority. These films ship sterile in packs of 100 in a mid-price tier.&nbsp; 
&nbsp;
For product details, compatibility guidance, or bulk requirements, <a href="https://mbpinc.net/contact-us">the MBP team </a>can help you select the right sealing film for your specific culture system.

Cell & Tissue Culture Film

AeraSeal™

AeraSeal™ (B-100) by MBP is a gas-permeable, hydrophobic plate sealing membrane with medical-grade, non-cytotoxic adhesive for cell, tissue, and bacterial culture. Rated &minus;20&deg;C to +80&deg;C. Available as sterile individual sheets (B-100: 100/pack; BS-25: 50/pack) or non-sterile roll stock for automation (RB-81x100). Ships ambient.

AeraSeal™, Sterile, Cell, tissue and bacterial cultures Temperature Range: -20°C to +80°C,100/Cs

AeraSeal™, Sterile, Cell, tissue and bacterial cultures Temperature Range: -20°C to +80°C, 50 Sealing Films/Pack

Roll Stock for Automation, AeraSeal™, Non-Sterile, 81mm x 100 meters (3.2" x 328’), 3" Cores

AeraSeal™ SealMate™ Rolls

AeraSeal™ SealMate™ Rolls (RSMB-2) by MBP provide gas-permeable, hydrophobic AeraSeal film in a roll format for faster plate sealing. Each roll contains 50 sheets separated by adhesive-free, perforated, color-coded red bands. 2 rolls/pk (100 sheets total). Non-sterile (RSMB-2) or sterile (RSMB-2-S). Rated &minus;20&deg;C to +80&deg;C. Ships ambient.

AeraSeal™ SealMate™ Rolls, 2 Rolls/Pk, 50 Sheets/Roll

AeraSeal™ SealMate™ Rolls, 2 Rolls/Pk, 50 Sheets/Roll, Sterile

AeraSeal™ SealMate™ Starter Kit

AeraSeal™ SealMate™ Starter Kit (SM-KIT-B) by MBP includes a re-usable SealMate dispenser and 2 rolls of perforated AeraSeal film (50 sheets/roll). Available non-sterile (SM-KIT-B) or sterile (SM-KIT-BS). Ships ambient.

AeraSeal™ SealMate™ Starter Kit, SealMate Dispenser + 2 Rolls of AeraSeal, 50 Sheets/Roll

AeraSeal™ SealMate™ Starter Kit, SealMate Dispenser + 2 Rolls of AeraSeal, 50 Sheets/Roll, Sterile

<h2 dir="ltr">What are PCR and qPCR sealing films?</h2>
 PCR and qPCR sealing films are optically clear microplate seals applied to 96- and 384-well PCR plates to create an airtight barrier through every thermal cycle, preventing evaporation, condensation, and cross-well contamination while still letting fluorescence pass through to the qPCR detector. Most are pressure-sensitive adhesive (PSA) or heat-activated films built on polypropylene or polyester (PET) with low-autofluorescence chemistry. Standard formats fit SBS sheets of approximately 137 &times; 80 mm. Buy from this category whenever the seal sits on a plate that will be thermally cycled or read in real time, not stored or incubated under simple lids. 
<h2 dir="ltr">What you will find:</h2>
&nbsp;
<ul>
<li dir="ltr" role="presentation">Optical-grade qPCR sealing films for fluorescence-based detection</li>
<li dir="ltr" role="presentation">Standard adhesive PCR films for routine thermal cycling</li>
<li dir="ltr" role="presentation">96-well microplate sealing films for standard PCR workflows</li>
<li dir="ltr" role="presentation">384-well compatible sealing films for high-throughput assays</li>
<li dir="ltr" role="presentation">High-temperature resistant films for -40&deg;C to 120&deg;C cycling</li>
<li dir="ltr" role="presentation">Low-evaporation sealing films for reaction stability</li>
<li dir="ltr" role="presentation">DNase/RNase-free films for contamination-sensitive assays</li>
</ul>
&nbsp;
<h2 dir="ltr">How to choose PCR or qPCR sealing film</h2>
 Confirm true optical clarity if you read fluorescence Not every "clear" sealing film has enough optical clarity and low enough autofluorescence for real-time PCR; choose a film specifically rated for qPCR with high light transmittance and no autofluorescence so excitation and emission pass cleanly. Standard storage films can suppress the signal. Decide between adhesive (PSA) and heat-seal Pressure-sensitive adhesive films are applied with a roller or paddle at the bench and peel off; heat-seal films bond under a plate sealer at controlled temperature and pressure for the strongest barrier in high-throughput and automated qPCR. PSA suits flexible workflows; heat-seal suits volume. Match the plate, thermal cycler, and skirt Confirm the film fits 96- or 384-well plates from your supplier and seats properly under the heated lid of your thermal cycler &mdash; full-skirt, semi-skirt, and non-skirt plates have different sealing surfaces. Sheet size near 137 &times; 80 mm is the SBS norm. Check chemical and temperature resistance PCR plate sealers and thermal cyclers reach 105 &deg;C routinely, and some films are rated to 150 &deg;C; check that the film and adhesive withstand the cycler protocol and the master mix without softening, lifting at corners, or leaving residue after peeling.
&nbsp;
<h2 dir="ltr">Specifications context</h2>
 Quality qPCR films are defined by light transmittance (typically &ge; 90 %), absence of autofluorescence, evaporation rate (commonly &le; 3 %), thermal tolerance to about 105 &deg;C with high-temperature variants to 150 &deg;C, and a DNase/RNase- and human-DNA-free certification appropriate for amplification. Most are supplied as flat SBS-format sheets around 137 &times; 80 mm, packed 100 per box; some have perforated end tabs for one-handed peeling. As of 2026, they sit in a low-to-mid price tier, with heat-seal films at the higher end.&nbsp; 
&nbsp;
<a href="https://mbpinc.net/contact-us">Connect with the MBP team today</a>&nbsp;to find the perfect optical or standard seal for your amplification workflow. Browse the wider&nbsp;<a href="https://mbpinc.net/consumables/sealing-films">sealing films range </a>for post-PCR archiving and reorder today via <a href="https://mbpinc.net/quickorder">Quick Order</a>.

DataSheet

AlumaSeal II™ PCR Plate Seals

AlumaSeal II™ (AF-100) by MBP stays flat during application with no roll-back. DNase/RNase-free, chemically resistant including DMSO, easily pierceable. Non-sterile AF-100 (100 seals/case) and sterile AFS-25 (&minus;80&deg;C to +120&deg;C, 50 films/pack). Ships ambient.

AF-100 Aluminum Foil Sealing Film for PCR Plates and Cold Storage 100 Seals/Case

AlumaSeal II™, Sterile, PCR, long-term storage, light sensitive assays and robotics, -80°C to +120°C, 50 Sealing Films/Pack

AlumaSeal®

AlumaSeal® by MBP is an easy-to-pierce aluminum foil plate seal rated &minus;80&deg;C to +120&deg;C — the widest temperature range in the MBP plate seal lineup. Secure seal, opaque barrier for light-sensitive samples. Available in 384-well CR (F-384-100) and 96-well (F-96-100) formats, 100 films/pack each. Ships ambient.

AlumaSeal 384™, CR, long-term storage, light sensitive assays and robotics, -80°C to +120°C, 100 Sealing Films/Pack

AlumaSeal 96™, long-term storage, light sensitive assays and robotics, -80°C to +120°C,100 Sealing Films/Pack

<h2 dir="ltr">What are cold storage sealing films?</h2>
 Cold storage sealing films are aluminum-foil or foil-laminate seals applied to microplates and deep-well storage plates to maintain an airtight barrier through long-term freezing, commonly rated to &minus;80 &deg;C and sometimes lower. Foil blocks light and gases, resists DMSO and organic solvents, and conforms to each well so the seal is visible and verifiable. Many are pierceable by pipette tips, needles, or robotic probes, and some heat-seal foils are autoclavable. Buy from this category for biobanking, compound-library archiving, and any sample set that must survive months at ultra-low temperature.
&nbsp;
<h2 dir="ltr">What you will find:</h2>
&nbsp;
<ul>
<li dir="ltr" style="color: #000000;" aria-level="1">
Cold storage sealing films for freezer and refrigeration use
</li>
<li dir="ltr" style="color: #000000;" aria-level="1">
Aluminum foil barrier films for long-term sample protection
</li>
<li dir="ltr" style="color: #000000;" aria-level="1">
High-performance adhesive films for evaporation control
</li>
<li dir="ltr" style="color: #000000;" aria-level="1">
Low-temperature resistant films for -20&deg;C to -80&deg;C storage
</li>
<li dir="ltr" style="color: #000000;" aria-level="1">
Pierceable films for post-storage sample access
</li>
<li dir="ltr" style="color: #000000;" aria-level="1">
Chemical-resistant sealing films for reagent stability
</li>
<li dir="ltr" style="color: #000000;" aria-level="1">
Microplate sealing films for cold chain workflows
</li>
</ul>
<h2 dir="ltr"> How to choose cold storage films</h2>
 Confirm the low-temperature rating Choose a film with a stated seal-integrity range that reaches &minus;80 &deg;C; some foils hold from &minus;80 &deg;C to +110 &deg;C, covering both freezer archiving and limited thermal steps.
Decide pierceable vs permanent Pierceable foils let robotic probes or pipette tips access wells without removing the seal &mdash; essential for automated biobanks; permanent heat-seal foils give a tamper-evident, near-irreversible barrier for long-term archiving.
Check chemical resistance For DMSO compound libraries and solvent-containing samples, confirm the foil is rated DMSO- and solvent-resistant so the seal and adhesive survive storage.
Match the application method Pressure-sensitive foils apply with a hand roller; heat-seal foils need a benchtop plate sealer and a compatible hot-melt adhesive, and will not bond with standard pressure-sensitive adhesives.
<h2 dir="ltr"> Specifications context</h2>
 Cold storage foils are defined by temperature range, adhesive type, chemical resistance, and whether they are pierceable. A foil rated &minus;80 &deg;C to +110 &deg;C covers freezer archiving and limited thermal cycling, while DMSO resistance matters for screening libraries. Heat-seal foils require a matched sealer and hot-melt adhesive, whereas pressure-sensitive foils are applied by roller. Because foil is opaque, plates are identified by a label on the foil or by position in the rack rather than read through the seal, so a clear labelling convention matters for retrieval.
&nbsp;
Protect your samples with confidence. Request product options, specifications, or bulk supply details. <a href="https://mbpinc.net/contact-us" style="color: #000000;">Contact the MBP team</a> and get the right sealing solution tailored to your cold storage workflow.

Cold Storage Film

AlumaSeal® CS™

AlumaSeal® CS™ (FC-100) by MBP is a cold-storage aluminum foil plate seal with a 50 &mu;m acrylic adhesive that maintains reliable adhesion down to &minus;80&deg;C. Optimized for long-term cryogenic plate storage. Non-sterile (FC-100, 100 films) or sterile (FCS-25, 50 films). Ships ambient.

AlumaSeal CS™, 100 Sealing Films/Pack

AlumaSeal CS™, Sterile, 50 Sealing Films/Pack

BrightMax™, Luminescence, fluorescence and microscopy, -40°C to +80°C, 50 Sealing Films/Pack

BrightMax™ (WT-50) by MBP is a white, light-reflecting vinyl plate seal for luminescence, fluorescence, and microscopy. Uniquely applicable to either the top or bottom of the plate — bottom application reflects and amplifies signal. 50 films/pack, rated &minus;40&deg;C to +80&deg;C. Ships ambient; single SKU.

EZ-Pierce

EZ-Pierce (EZP-100) by MBP is a pierceable adhesive plate sealing film that allows clean well access via pipet tip or dispensing needle without removing the full seal. Non-sterile (EZP-100) and sterile (EZPS25) variants available. Ships ambient; store at room temperature.

EZ-Pierce™, 100/Cs

EZ-Pierce™, Sterile,50/Cs

EZcap™ FoilStrips™, 6 Strips per Sheet, 1X8 Rows per Strip

EZcap™ FoilStrips™ (F2CS1X8300) by MBP are precision-cut aluminum foil strip seals for PCR 8-tube strips or single rows of 96-well PCR or deep-well storage plates. 6 strips/sheet, 1&times;8 rows/strip. Remove easily with no splash back. Single SKU. Ships ambient.

EZcap™ PCR FilmStrips™, 8 Strips per Sheet, 1X8 Rows per Strip, For sealing a PCR 8-tube strip or a single row of a 96-well plate, 400/Pack

EZcap™ PCR FilmStrips™ (US-CS1X8-400) by MBP are adhesive peel-and-stick alternatives to PCR strip-caps — no sore thumbs. 8 strips/sheet, 1&times;8 rows/strip; compatible with PCR 8-tube strips and single 96-well plate rows. 400 strips/pack. Ships ambient; single SKU.