SDS6
Overview
A set of 6mm diameter (ID) hardened steel dry pressing die set for pellet presses, ready for you to make 6mm diameter cylinder-shape pellets.
Die set includes
- Three 6mm ID cylinder-shape core dies made of polished hardened steel
- One steel sleeve
- One steel support plate
- Two push rods
- One pellet ejector
Important
- Always wear protection goggles during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 4 tons. Across International is not responsible for any damage caused by misuse.
SDS8
Die set includes
- Three 8mm OD cylinderical core dies made of highly polished hardened steel
- One steel sleeve
- One steel support plate
- Two push rod
- One pellet ejector
- One aluminum case
CAUTION
- Always wear protection goggles and gear during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 8 tons. Across International is not responsible for any damage caused by misuse.
SDS10
Overview
A set of 10mm diameter (ID) hardened steel dry pressing die set for pellet presses, ready for you to make 10mm diameter cylinder-shape pellets.
Die set includes
- Two 10mm ID cylinder-shape core dies made of highly polished hardened steel
- One steel sleeve
- One steel support plate
- One push rod
- One pellet ejector
Important
- Always wear protection goggles and gear during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 10 tons. Across International is not responsible for any damage caused by misuse.
SDS13
Overview
A set of 13mm diameter (ID) hardened steel dry pressing die set for pellet presses, ready for you to make 13mm diameter cylinder-shape pellets.
Die set includes
- Two 13mm ID cylinder-shape core dies made of highly polished hardened steel
- One steel sleeve
- One steel support plate
- One push rod
- One pellet ejector
Important
- Always wear protection goggles during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 15 tons. Across International is not responsible for any damage caused by misuse.
SDS15
Overview
A set of 15mm diameter (ID) hardened steel dry pressing die set for pellet presses, ready for you to make 15mm diameter cylinder-shape pellets.
Die set includes
- Two 15mm ID cylinder-shape core dies made of highly polished hardened steel
- One steel sleeve
- One steel support plate
- One push rod
- One pellet ejector
Important
- Always wear protection goggles during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 20 tons. Across International is not responsible for any damage caused by misuse.
Â
SDS20
Overview
A set of 20mm diameter (ID) hardened steel dry pressing die set for pellet presses, ready for you to make 20mm diameter cylinder-shape pellets.
Die set includes
- Two 20mm ID cylinder-shape core dies
- One steel sleeve
- One steel support plate
- One push rod
- One pellet ejector
Important
- Always wear protection goggles during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 25 tons. Across International is not responsible for any damage caused by misuse.
SDS25
Overview
A set of 25mm diameter (ID) hardened steel dry pressing die set for pellet presses, ready for you to make 25mm diameter cylinder-shape pellets.
Die set includes
- Two 25mm ID cylinder-shape core dies made of highly polished hardened steel
- One steel sleeve
- One steel support plate
- One push rod
- One pellet ejector
Important
- Always wear protection goggles during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 30 tons. Across International is not responsible for any damage caused by misuse.
SDS30
Overview
A set of 30mm diameter (ID) hardened steel dry pressing die set for pellet presses, ready for you to make 30mm diameter cylinder-shape pellets.
Die set includes
- Two 30mm diameter cylinder-shape core dies
- One sleeve
- One support base
- One push rod
- One pellet ejector
Important
- Always wear protection goggles during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 40 tons. Across International is not responsible for any damage caused by misuse.
SDS40
Overview
A set of 40mm diameter (ID) hardened steel dry pressing die set for pellet presses, ready for you to make 40mm diameter cylinder-shape pellets.
Die set includes
- Two 40mm diameter cylinder-shape core dies
- One sleeve
- One support base
- One push rod with the attachable handle
- One pellet ejector
Important
- Always wear protection goggles during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 45 tons. Across International is not responsible for any damage caused by misuse.
SDS50
Overview
A set of 50mm diameter (ID) hardened steel dry pressing die set for pellet presses, ready for you to make 50mm diameter cylinder-shape pellets.
Die set includes
- Two 50mm ID cylinder-shape core dies made of highly polished hardened steel
- One steel sleeve
- One steel support plate
- One push rod
- One pellet ejector
Important
- Always wear protection goggles and gear during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 100 tons. Across International is not responsible for any damage caused by misuse.
SDS76
Overview
A set of 76mm diameter (ID) hardened steel dry pressing die set for pellet presses, ready for you to make 76mm diameter cylinder-shape pellets.
Die set includes
- Two 76mm ID cylinder-shape core die made of highly polished hardened steel
- One steel sleeve
- One steel support plate
- One push rod with detachable handle
- One pellet ejector
Important
- Always wear protection goggles during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 150 tons. Across International is not responsible for any damage caused by misuse.
SDS100
Overview
A set of 100mm diameter (ID) hardened steel dry pressing die set for pellet presses, ready for you to make 100mm diameter cylinder-shape pellets.
Die set includes
- Two 100mm diameter cylinder-shape core dies made of highly polished hardened steel
- One steel sleeve
- One steel support plate
- One push rod with detachable handle
- One pellet ejector
Important
- Always wear protection goggles and gear during operation
- Clean the die set throughout with absolute ethyl alcohol and keep them in a dry box with silica gel after use to avoid rusting on the surface.
- Never fill the die more than 1/3 its sleeve height with your sample and do not apply pressure beyond 250 tons. Across International is not responsible for any damage caused by misuse.
| SDS6 | SDS8 | SDS10 | SDS13 | SDS15 | SDS20 | SDS25 | SDS30 | SDS40 | SDS50 | SDS76 | SDS100 | |
| Maximum Pressure | 4 tons | 8 tons | 10 tons | 15 tons | 20 tons | 25 tons | 30 tons | 40 tons | 45 tons | 100 tons | 150 tons | 250 tons |
| Rockwell Hardness | Rc 62 | |||||||||||
| Diameter (ID) | 6mm | 8mm | 10 mm | 13 mm | 15 mm | 20 mm | 25 mm | 30 mm | 40 mm | 50 mm | 76 mm | 100 mm |
| Height | 47 mm (assembled without sample) | 69 mm (assembled without sample) | 61 mm (Assembled without sample) | 75 mm (Assembled without sample) | 90 mm (Assembled without sample) | 94 mm (Assembled without sample) | 105 mm (Assembled without sample) | 110 mm (assembled without sample) | 123 mm (Assembled without sample) | 135 mm (Assembled without sample) | 135 mm (Assembled without sample) | 300 mm (Assembled without sample) |
| Sleeve Height | 25mm | 39 mm | 39 mm | 40 mm | 45 mm | 46 mm | 50 mm | 60 mm | 60 mm | 70 mm | 80 mm | 120 mm |
| Sleeve Diameter (OD) | 25mm | 30 mm | 30 mm | 39 mm | 39 mm | 46 mm | 46 mm | 48 mm | 60 mm | 78 mm | 115 mm | 150 mm |
| Tolerance | 0.01-0.02 mm (10-20 micron) | |||||||||||
| Max sample fill height | Not to exceed 1/3 of the sleeve height | |||||||||||
| Material | W18Cr4V hardened carbon tool steel | |||||||||||
Reviews
There are no reviews yet.